| TECHNICAL DATA SHEET-UMG 507 |
| Weight |
850g |
| Calorific value |
2.2 MJ (610Wh) |
| Installed location |
any |
| Connectable cables |
| Solid, stranded, flexible |
0.08 – 2.5 mm2 |
| Plug connector, wire end ferrule |
1.5 mm2, only one conductor may be connected per terminal connection |
| AMBIENT CONDITIONS |
| Operating Temperature range |
- 10° C .. + 55° C |
| Storage Temperature range |
- 20° C .. + 70° C |
| Relative Air Humidity |
15% up to 95% without dew |
| Operating Height |
0 .. 2000m over sea level |
| Protection Class |
| Front Side |
IP50 according to IEC529 |
| Front with seal (option) |
IP65 according to IEC529 |
| Back Side |
IP20 according to IEC529 |
| Plug Screw |
IP20 according to IEC529 |
| Auxiliary Power (see rating plate) |
300V CAT III |
| Test Voltage |
3150V DC |
| Range 1 (standard) |
85 .. 265 V AC, 80 .. 370 V DC |
| Range 2 (option) |
40 .. 115 V AC, 55 .. 165 V DC |
| Range 3 (option) |
15 .. 50 V AC, 20 .. 70 V DC |
| Back-up fuse |
4 A .. 10 A (medium time lag) |
| Power Consumption |
4 A .. 10 A (medium time lag) |
| MEASUREMENT |
| Current Measurement |
| Overvoltage category |
300V CAT II, 150 V CAT III |
| Test voltage |
300V CAT II, 150 V CAT III |
| Power Consumption |
Approx. 0.2 VA |
| Nominal Current for |
.. / 5 A (../1A) 5A (1A) |
| Limit Current |
9.5 Amps (Sinusoidal) |
| Overload, Continuous |
6 Amps (Sinusoidal) |
| Overload 60 Amps for |
60 Amps for 1 sec. |
| Voltage Measurement |
| Overvoltage category |
500V CAT III |
| Test voltage |
4200 V DC |
| Impedance |
4Mohm / Phase |
| Power Consumption |
Approx. 0.1 VA |
| Measuring range L – N |
50 .. 500 V AC |
| Measuring range L – L |
90 .. 870 V AC |
| Frequency of the fundamental component |
45 Hz .. 65 Hz |
| INPUTS AND OUTPUTS |
| Digital Inputs and Outputs |
| Overvoltage category |
32V CATI |
| Refreshment rate – inputs, outputs, flags |
50 Hz 200ms; 60 Hz 167ms |
| 6 Digital inputs |
| Max. Counting Frequency |
20 Hz |
| Current input |
Approx. 1 mA .. 6 mA |
| 6 Digital outputs, positive switching (not short-circuit proof) As Switching Output |
| Switching voltage |
Max. 28V DC |
| Switching Current |
Max. 30 mA |
| Switching Frequency (50Hz system) |
Max. 2.5 Hz |
| Switching Frequency (60Hz system) |
Max. 3.0 Hz |
| Auxiliary Voltage, external |
20 V .. 28 V DC |
| As pulse output (S0) |
|
| Switching Frequency |
Max. 20 Hz |
| Switching Current |
Max. 30 mA |
| Maximum Cable length |
100m |
| Auxiliary voltage, external |
20 V .. 28 V DC |
| Analog inputs and outputs (options) |
| Overvoltage category |
32V CATI |
| Accuracy |
+-1.5% vMb |
| 2 Analog outputs |
0/4 .. 20 mA |
| Burden |
Max. 300 Ohm |
| External Auxiliary Power |
20 V .. 28 V DC |
| Residual Ripple |
Max. 2V, 50 Hz |
| 1 analog input |
“ 0 .. 20 mA” 0 .. 20 mA |
| 1 analog input |
“ PT100” PT 100, PT 1000, KTY83, KTY84 |
| Interface (options) |
| Overvoltage category |
32V CATI |
| RS 232 |
3 – pin scre-plug in terminals. |
| Protocol |
MODBUS RTU |
| Transfer rate |
38.4 kBit/s |
| RS485 (Option) |
Connector, SUB D 9-pin |
| Protocol, Profibus (option) |
Profibus DP/V0 to EN 50170 |
| Transfer rates |
9.6k Baud up to 1.5 M Baud |
| Protocol, Modbus RTU |
Modbus RTU/Slave, RTU/Master |
| Transfer rates |
9600 bps, 19.2 kbps, 38.4 kbps, 115.2 kbps |
| Ethernet 10/100 Base-TX (option) |
| Connection |
RJ-45 |
| Functions |
Modbus Gateway, Embedded Webserver |
| Protocols |
TCP/IP, EMAIL(SMTP), DHCP(BootP), Modbus-TCP, Modbus over Ethernet, Ping, NTP. |
