• Energy Management Systems - Baron Power
  • Products > Energy Management System

The first step towards saving energy and improving operational processes is the measurement of the most important parameters of your electrical energy supply while monitoring the peak loads. Baron offers Frako’s complete range of power monitoring units with the corresponding accessories – The EMR Series.These equipments and power analyser help you gain a comprehensive overview of your energy supplies and introduce the correct measures. The power quality is also monitored according to the general valid standards (e.g. EN50160). For more information click on the tabs below.

Central Units

ems1
Power supply
Supply voltage 230 VAC +/- 10 %
or (switchable): 110 VAC +/- 10 %
Frequency 45 up to 65 Hz
Fuse Protection max. 50 VA
Interfaces
1 Ethernet RJ45, connection of LAN Network
Protocol: TCP/IP
Transmission: 100BaseTx full duplex
2 serial interfaces 9 pole Sub-D-bush (male),RS232 for by dial-up or direct connection
high transmission rate: up to 115200 Baud
FRAKO Starkstrombus® electrical connection: according norm EIA RS 485
high transmission rate: 76.8 kbit/sec
Protocol: FRAKO Starkstrombus®
Display-/Operating elements 3 LEDs, 4 operating buttons, bright LC-Display
Outputs
3 alarm signalling potential-free normal open contact,free programable
contamination: max.48 V AC/DC, max.1 A
Mechanical construction
Dimensions 300x75x220 mm (WxHxD)
Ingress protection Enclosure IP40, Terminals IP20
Housing material metal housing
Orientation standing / vertical
Weight 3.40 kg
Ambient temperature 0 up to +50°C
PC-Requirements for the Software package FRAKO-Net
Hardware
Pentium min. 2 GHz clock frequency
working memory min. 1 GB RAM
free hard disk capacity 6 GB
Ethernet 10/100 MB network connection or/and one free serial interface
CD-ROM-drive
SVGA-Graphic card
colour screen with minimum resolution of 1024 x 768
Software
Windows 2000 pro SP3
Windows XP pro SP3
Windows 2003 Server
Internet Explorer 5.5
Article-No EMIS 1500 S: 20-10081 EMIS 1500 M: 20-10082 EMIS 1500 L: 20-10083 EMIS 1500 XL: 20-10084 EMIS 1500 XXL: 20-10085

Gateway

Power supply
Mains voltage 230 VAC +/- 10 %
Frequency 45 up to 65 Hz
Power consumption approx. 10 VA
Fuse protection max. 2 A external required
Interfaces
1 Ethernet RJ45, to connection on LAN Network
Protocol: TCP/IP
transmission: 10BaseT half duplex
1 FRAKOStarkstrombus® for connection to the FRAKO Energy Management System, according to EN 50170(P-Net) standardised fieldbus, RS 485
Transfer speed: 76.8 kbit/s
1 Serial interface 9 polige Sub-D-bush (female), RS 232 V.24, to device configuration
Protocol: FRAKO internally
high transmission rate: 115200 Baud, 8 Bit, 1 Stopbit,no equality
Display elements 4 light-emitting diodes
Connections screw terminals
wire cross-section: max. 2.5 mm²
Mechanical construction
Dimensions 140x90x59 mm (WxHxD), DIN module case 8 TE
Ingress Protection housing/terminals IP40/20
Construction Protection class II at VDE 0411 / DIN EN 61010-1
Cases flame-retardant UL94-V0
Fitting on standard rail 35 mm according to DIN EN 50022
Mounting position optional
Weight approx. 0.5 kg
Operating Conditions
Ambient temperature 0 up to +50°C
Article-No. 20-10210

System Timer

Power supply
Mains voltage 230 VAC +/-10 %
Frequency 45 up to 65 Hz
Power consumption approx. 5 VA
Fuse protection max. 2 A external required
Interfaces
Serial A 25 pole Sub-D-bush (female), for connection of EM-DCF77 radio clock
Serial B 9 pole Sub-D-bush (female), RS 232, for connection of a PC
FRAKO Starkstrombus® For connection to the FRAKO Energy Management System, according to EN 50170(P-Net) standardized fieldbus, RS 485
High transmission rate: 76.8 kbit/s
Display elements 3 light emitting diodes
Connections in housing with screw terminals
conductor cross-section: max. 2.5 mm²
Mechanical construction
Dimensions 158x75x120 mm (WxHxD)
Ingress protection IP40
Version according to VDE 0411 protection class I (also DIN EN61010-1)
Material of case PC with 10% GF, V-0 flame-adversely UL-94 V-0
Installation screw mounting or standard rail 35 mm according to DIN EN 50022
Orientation optional
Weight approx. 0.8 kg
Operating conditions
Ambient temperature 0 up to +40°C
PC-requirements for the Softwarepackage EMT-SW
Hardware
Pentium min. 1 GHz clock frequency
working memory min. 512 MB RAM
free hard disk capacity 10 MB
Ethernet 10/100 MB network connection or/and one free serial interface
CD-ROM, SVGA-Graphic card
colour screen with minimum resolution of 1024 x 768
Software
Windows 2000 pro SP3
XP pro SP3
2003 Server, IE5
Article-No. 20-10300

Communications Processor

Power supply
Mains voltage 230 VAC +/-10 %
Frequency 50 to 60 Hz
Power consumption max. 3 VA
Fuse protection max. 2 A external required
Outputs
serial interfaces A 25 pole Sub-D-bush (female), RS 232, framework protocol 3964R, data protocol RK 512
serial interfaces B 9 pole Sub-D-bush (female), RS 232, for a connection of a PC
FRAKO Starkstrombus® for connection to the FRAKO Energy Management System, according to EN 50170(P-Net) standardised fieldbus, RS 485
Transfer speed: 76.8 kbit/s
Display elements 3 light emitting diode
Connections in cases via connector strip
Mechanical construction
Dimensions 158x75x120 mm (WxHxD)
Ingress protection IP50
Version Protection class I according to VDE 0411 / EN 61010
Case flame-adversely UL94-V0 (according to the manufacturer)
Installation screw mounting or standard rail 35 mm according to DIN EN 50022
Mounting position optional
Weight approx. 0.8 kg
Operating Conditions
Ambient temperature 0 up to +40°C
PC-Requirements for the Softwarepackage
Hardware
Pentium mind. 1 GHz clock frequency
working memory min. 512 MB RAM
free hard disk capacity10 MB
Ethernet 10/100 MB network connection or/and one free serial interface
CD-ROM
SVGA-Graphic card
colour screen with minimum resolution of 1024×768
Software
Windows 2000 pro (min. SP3)
Windows XP pro (min. SP1)
Windows 2003 Server (min. SP1)
Internet Explorer 5.5
Article-No. 20-10202

Optimization Controller

Power supply
Mains voltage 100 V – 253 V AC or 100 V – 230 V DC
Frequency 45 up to 65 Hz
Power consumption 7 W / 18 VA
Inputs
General S0-Interfaces(DIN43864) for connection of potential free contacts
Voltage with open contact: 15 V
Max. Line resistance: 800 Ohm
Short-circuit current: 18 mA
Pulse frequency: 0.1 to 20 Hz
3 Pulse Inputs for power data acquisition from up to 3 meters with pulse outputs. Input 3 can also be used for acquiring reactive power data.
1 Receiver 1…1440 Minutes
2 Profil Inputs to the selection of 4 profiles
Outputs
5 Relaiskontakte(swichting channels) bistable, 250V / 2A AC or 30V / 2A DC
1 Relaycontact(distress throwing off channel) bistable, 250V / 2A AC or 30V / 2A DC
1 alarm contact break contact 250V / 2A AC or 30V / 2 A DC
1 Extension bus-interface for connection up to 10 EMD1101
1 FRAKO Starkstrombus-Interface for connection to FRAKO Energy Management System
Displaybus-Interface for optional connection of max. 2 external Displays of Type EM-FD 2500
Operating elements Operation via external display EM-FD 2500
Display elements 15 LEDs
Connections via plug-in terminals
conductor cross-section: max. 1.5 mm²
Fuse Protection max. 2A external required
Mechanical construction
Dimensions 296 x 260 x 133 mm (WxHxD)
Ingress Protection IP30 (cases), IP10 (terminals)
Weight approx. 0.4 kg
Protection class Protection class II according to DIN/EN 61010
Housing flame-adversely UL 94-V0
Installation on standard rail 35 mm according to DIN EN 50022
Operating Conditions
Ambient temperature 0°C up to +45°C
Storage temperature -20°C up to +60°C
PC requirement for Device-Manager
Hardware
PC: CPU with min. 2 GHz, 1 Gbyte RAM, 200 Mbyte free hard disk capacity
Software:
Windows XP, SP 2 with installed.NET-Framework 3.5
Windows 7 (32 or 64 Bit)
Windows 2008 Server R2
Article-No. 20-20071

Extension Module-Single Throw

Power supply
Mains voltage 230 VAC -15 % up to +10 %
Frequency 45…65 Hz
Power consumption 4 VA
Fuse Protection max. 2 A external required
Outputs
8 Switching Channels normal open contact 250 VAC / 4 A
1 Extension bus / FRAKO Starkstrombus® 2-Wire-fieldbus, RS 485
Operating elements 8-fold DIP-switching series, 10-level rotary switch
Display elements 9 light emitting diode
Connections in cases via connector strip
conductor cross-section: max. 2.5 mm²
Mechanical construction
Dimensions 158x75x120 mm (WxHxD)
Ingress Protection IP40
Version Protection class 2 nach DIN/EN 61010
Housing flame-adversely UL94-V0 (according to the manufacturer)
Installation screw mounting or standard rail 35 mm according to DIN EN 50022
Mounting position wall mounting, vertical
Weight approx. 0.8 kg
Operating Conditions
Ambient temperature 0 up to +45°C
storage temperature -20 up to +60°C
Article-No. 20-21002

Mains Analysis Devices for Top-Hat Rail Mounting

EM-PQ 2300 EM-PQ 2200 EM-PQ 2100 EM-PQ 1500 M
Voltage 90-267 VAC or 100-360 VDC 95-240 VAC; 135-340 VDC ± 10% 95-240 VAC; 135-340 VDC ± 10% removed from rated voltage
Frequency 45…65 Hz 45/65 Hz 45/65 Hz 50 Hz
Power consumption max. 8 W max. 9 VA max. 9 VA max. 7 VA
Contact termination 3/4/5-Conductor ● / ● / ● ● / ● / – ● / ● / – ● / ● / -
Current-Measurements Input 5 x X/5A 4 x X/1A, X/5A 4 x X/1A, X/5A 3 x X/5A (transformer current > 6 mA), galvanical isolated
Voltage-Measurements Input 400/690 VAC (L-N/L-L) 3-phases 5-conductor system 277/480 VAC (L-N/L-L) 3-phases 4-conductor system 480 VAC (L-L) 3-phases 3-conductor system 277/480 VAC (L-N/L-L) 3-phases 4-conductor system 480 VAC (L-L) 3-phases 3-conductor system 3 x 57-230 VAC ± 10% (external-/neutral conductor) 3 x 100-400 VAC ± 10% (external-/neutral conductor)
Harmonics V/A 1-51 1-63 1-40
Short Interruption
Active Energy Class 1 0,5 (…/5A); 1 (…/1A) 0,5 (…/5A); 1 (…/1A) 1
Analoge In-/Outputs – / 2 (0-10 V or 0-20 mA or 4-20 mA) 1 temperature / – 1 temperature / – – / 1 (max. 30 VDC, 100 mA), (4-20 mADC passiv)
Digitale In-/Output 4 / 2 2 / 2 2 / 2 – / 1 (max. 48 VDC, 100 mA); 1 (max. 30 VDC, 100 mA)
Memory Min-/Maxvalue
Memory size 256 MB 128 MB 128 MB
Interfaces
Ethernet
FRAKO Energy Management System ● via FRAKO Starkstrombus®Intranet (Ethernet)Modbus/TCP ● Connection via- Modbus RTU (RS 485) or – Modbus/TCP (Ethernet) ● Connection via- Modbus RTU (RS 485) or – Modbus/TCP (Ethernet) ● via FRAKO Starkstrombus®
RS 232 / RS 485 – / ● ● / ● ● / ● – / –
Profibus DP – / –
Webserver / Email – / ● ● / ● ● / ● – / –

Mains Analysis Devices

EM-PQ 3000 EM-PQ 2500 EMA 1101 EMA 1296
Voltage 95-240 VAC; 80-340 VDC ± 10% 95-240 VAC; 80-340 VDC ± 10% 230 VAC ± 10% 110-440 VAC oder 120-350 VDC ± 20%
Frequency 45/65 Hz 45/65 Hz 48…62 Hz 50/60 Hz ± 10%
Power consumption max. 9 VA max. 9 VA max. 7VA max. 5VA
Contact termination 3/4/5-conductor ● / ● / – ● / ● / – ● / ● / – ● / ● / -; 2-conductor and single-phase
Current-Measurements 4 x X/1A, X/5A 4 x X/1A, X/5A 3 x X/5A (Wandlerstrom > 6 mA), galvan. getrennt 3 x X/5A (X adjustable of 5-9999 A); 3 x 50-500 VAC (external-/external conductor), Overload 800 VAC;
Voltage-Measurements 417/720 VAC (L-N/L-L) 3-phases 4-conductor systems 480 VAC (L-L) 3-phases 3-conductor systems 417/720 VAC (L-N/L-L) 3-phases 4-conductor systems 480 VAC (L-L) 3-phases 3-conductor systems 3 x 250-550 VAC (external-/external conductor) 1);3 x 50-105 VAC (external-/external conductor) 2) 3 x 28-289 VAC (external-/neutral conductor), Overload 800 VAC
Harmonics V/A 1-63 1-40 1-19
Short Interruption
Active Energy Class 0.2 (…/5A) 0.2 (…/5A) 2 2
Analoge In-/Outputs – / – – / – 2 temperature inputs3) / – – / –
Digitale In-/Outputs 8 / 5 8 / 5 Collective input for selection of 2 profiles/ 1 alarm signalling contact 250 VDC, max. 3 A – / optional Plug-In Module for active- and reactive working
Memory Min-/Maxvalue
Memory size 256 MB 256 MB
Interfaces
Ethernet
FRAKO Energie-Management-System ● Connection via- Modbus RTU (RS 485) or – Modbus/TCP (Ethernet) ● Connection via- Modbus RTU (RS 485) or – Modbus/TCP (Ethernet) ● via FRAKO Starkstrombus® ● optional Plug-In module enable the connection via Modbus RTU
RS 232 / RS 485 – / ● – / ● ● (optional at EMA 1101, EMA 1101 105 V) / – – / –
Profibus DP ● (only -DP – Variantes)
Webserver / Email – / – ● / ● – / – – / –

Display Unit

EM-FD 2500 EM-FD 1500
Voltage über EM-Gerät versorgt 24 VDC ± 15% or 85-264 VAC
Frequency 50/60 Hz
Power consumption max. 3 VA max 3 VA
Operating-/Displayelement 9 Buttons / bright LC-Display / 1 LED 9 Button / bright LC-Display
Interfaces
CAN-Bus
RS 232 / RS 485

Power Factor Control Relay with Bus Interface

Power supply
Mains voltage 230/400 VAC -15 % up to +15%
Frequency 48 up to 62 Hz
Power consumption 9 VA at 0 resp. 13 VA at 12 switching control contacts
Fuse Protection max. 4 A external required
Measurements Inputs
Voltage circuit: 100 VAC to 690 VAC +/- 10 %, Power consumption: 0.5 VA
Voltage circuit for current transformer X/1 A bis X/5 A (min. transformer current > 20 mA), Power consumption: max. 1.8 VA at 5 A transformer-rated current
Outputs
12 control contacts: Relay contacts, potential-free,
switching voltage: 380 VAC according to VDE0110 group B, 250 VAC according to VDE0110 group C,
total switching current: 2 x 5 A,
switching capacity: 1800 VA
1 alarm signalling contact: 250 VAC/ 4 A, potential-free, closed on alarm
Inputs
1 tariff input choice of 2 separate control programs (z.B. HT/NT)
Interfaces (Mode of operation optionally)
1 FRAKOStarkstrombus® for connection to FRAKO Energy Management System, according to EN 50170(P-Net) standardised fieldbus, RS 485
transfer speed: 76.8 kbit/s
1 RS 232-Interface via RS232-Adapter (Option) direct connection to the PC
transfer speed: 19200 Baud
Undervoltage control bei Netzunterbrechung im Spannungspfad > 15ms werden zugeschaltete Kondensatorstufen abgeschaltet, bei Wiederkehr werden benötigte Stufen zugeschaltet
Operating elements membrane keyboard with 4 buttons
Display elements 18 light emitting diodes, 4 1/2-digit numeric display
Connections via connector strips (included with delivery)
Mechanical construction
Dimensions front panel dimension: 144×144 mm (DIN 43700)
switch panel aperture: 138×138 mm (DIN 43700)
installation depth: 105 mm
Ingress Protection cases/terminals IP53/20 (when using the sealing ring as an accessory)
Version Protection class II according to VDE 0160, Isolation groupe B (when using the insulated fastening screws as accessories)
Housing flame-adversely UL94-V0
Installation From the front panel using a screwdriver
Mounting position optional
Weight approx. 1.2 kg
Operating Conditions
Ambient temperature -25°C bis +60°C according to DIN VDE 0660, Part 500 paragraph.6.1.1.1
Article-No. 20-50006

Visualization Software

PC-requirements for small and medium systems:
Hardware
min. 3 GHz Processor Dual-Core
4 GB working memory
1 GB free hard disk memory
Software
Windows 7 (x32/x64)
Windows Server (2003 R2/2008 R2)
Windows DOT NET 4.0 SP1
* registered trademarks of Microsoft Coorporation
FRAKO-NET V1.24.0000 (or newer)
SQL database Firebird 2.0 (included in FRAKO-NET)
Article-No. 20-10649

Cost Center Handling Software

PC-requirements:
Hardware
Pentium, mind. 2 GHz clock frequency
min. 1 GB working memory
6 GB free hard disk memory
Ethernet 10/100 MB network connection or/and one free serial interface
CD-ROM-drive
SVGA-graphic card
Colour screen, minimum resolution: 1024 x 768 Pixel
Software
Database FRAKO-NET DB or FRAKO EMIS-DB
Windows 2000 pro (min. SP3)
Windows XP pro (min. SP1)
Windows 2003 Server (min. SP1)
Internet Explorer 5.5
Excel (from Version 2000)
* registered trademarks of Microsoft Coorporation
Article-No. 20-10488

EMG-OPC-Server

PC-requirements for small and medium systems:
Hardware
Pentium, mind. 1 GHz clock frequency
min. 512 MB working memory
10 MB free hard disk memory
Ethernet 10/100 MB network connection or/and one free serial interface
CD-ROM drive
SVGA-graphic card
colour screen with minimum resolution of 1024 x 768
Software
Windows 2000 pro (min. SP3)
Windows XP pro (min. SP1)
Windows 2003 Server (min. SP1)
Internet Explorer 5.5
SQL database Firebird 2.0 (included in FRAKO-NET)
Article-No. 20-10649